Weber P40 Max² 25 KG - Polystyrene insulating systems adhesive

Product code: APN-26
Delivery time:
Check to see when you can receive your order.
Benefits:
See some advantages of purchasing from PIATRAONLINE:
  • generic
    Door-to-door delivery
  • generic
    Huge stocks available
  • generic
    6 days call center help
  • generic
    More than 40.000 happy clients
Suggest to your friends:
Did you like this product? Or you need another opinion? Share this on your social networks.
info
1 Piece = 1 Bag
500 EUR/Bag
+
Bag
Price without VAT
Product available by order
Preț final:
500 EUR
Price without VAT
phone_product_help
Need our help?

Product description

This thermal insulation systems adhesive, the Weber P40 max² is used for bonding and reinforcement of polystyrene foam, polystyrene graphite and mineral wool (basalt). It is applied on all conventional surfaces: concrete, light concrete, porous concrete, cement plaster, cement-lime plaster,  old plaster and directly onto any type of masonry. It is recommended for thermal insulation of newly built and old buildings(rehabilitation). This adhesive for thermal insulation systems has demonstrated its full utility in time, confirming the trust specialists put in this product.

Made from cement and mineral fillers, contains synthetic resin of professional quality.

Grey-colored polystyrene adhesive.

Surface it is applied on:
Gluing: surfaces of concrete, lightweight cellular concrete, lime-cement plaster, plaster old, and direct any type of masonry.
Reinforcement: expanded polystyrene tiles, graphited polystyrene and mineral wool.

Support surface preparations:
Surfaces must be clean, undeformable, fix and dry, polystyrene's sides must be cleaned and free of grease, oil, dust or other impurities. If the surfaces are very porous, they should be watered, and then wait until the film of water disappears.

How to prepare and use:
Pour the contents of one bag in 7 liters of water and mix manually or mechanically using an electric mixer until you get a homogeneous paste.

After obtaining the paste, it is left for 5 minutes, then remix for 30 seconds.

For gluing: the obtained adhesive mortar is applied on the perimeter of the polystyrene slab on edge's length in several points (3-6) so that by pressing, the adhesive coated surface is greater than 40%. Fixed by manually pressing, while flatness and verticality is adjusted using screed and spirit level.

For reinforcement: the adhesive mortar is applied using a jagged trowel (6x6 or 8x8 mm) in a uniform layer on the surface of the tile. the reinforcement net (made from fiberglass) is incorporated in the adhesive on a vertical direction with the help of plastering tools so that the net strips have a minimum of 10 cm overlap. Immediately apply the second coat of paste (with a thickness of approx.15 mm), plastering in such a way that the mesh surface is fully covered.

Recommendations:
The minimum work temperature is + 50C and + 300C maximum. During the work, the surface must be protected from the strong rays of the sun and rain. cladded surface and used material must not be exposed to frost or rain for 24 hours after application. In cold weather and high humidity, the doweling of insulating tiles is done only after waiting for a suitable time (a dowel trial).

Use characteristics:
Waiting time: 5 minutes from mix preparation
Time to use: approx. 3 hours from mix preparation
The duration of the drying and maturation is given for a temperature of 20C degrees Cand a relative humidity of 65%. Higher values shorten the duration, while lower values lengthen it.
Contains cement. Makes alkaline reaction with water. Protect eyes and skin. In case of contact with eyes they should be washed with plenty of water and seek a medical specialist's advice.

Technical specifications:
Initial traction adhesion: > 0 8 N/mm2.
Slippage: < 0 5 mm.
Mechanical compression resistance: ≥ 15 N/mm2

Validity term:
12 months from date of manufacture when stored on wooden pallets in dry conditions

Consumption:
Gluing: 4-6 kg/sqm
Reinforcement: 3-4 kg/sqm

Product specification

Color variation
Small
Delivery
Order now and we will dispatch it by truck in Europe or by container internationally. Regardless of quantity, our shipping cost will be low. To find out our shipping price, just give us a call.
Minimum order quantity
1 Sack
Packing
Pallet
Packing details
Pallet: 42 bags / 1050 kg
Product code
APN-26
Specific observations
Pallet
Specific observations or benefits
Bag 25kg - pallet 42 Bags - 1050kg
Suitable for:
Interior - wall cladding
Exterior - wall cladding
Weight (U.M.)
25
Weight per piece (kg)
25 kg

Comments or reviews:

For the moment there are no comments from our users.
Write a comment or a review!
Have you bought or tested this product? We want to know your opinion, either bad or good! Write a review and help other users to make a choice as inspired as yours!
Rating:
star
star
star
star
star
Name
E-mail
Subject
Comment
All the fields are required.
By publishing a review on our site, you agree with our terms and conditions.

Recommended for:

  • Facade / Fence / Home-Base

Suitable for:

  • Interior - wall cladding
  • Exterior - wall cladding

PIATRAONLINE certifications

Similar products

Weber P40 Max² 25 KG - Polystyrene insulating systems adhesive https://www.piatraonline.com/userfiles/ba2b7a23-180a-4450-af7d-24f81a3361c7/products/3324738_list.jpg Weber Saint Gobain Romania
5.95 EUR Product available by order